Browse Our Swung Glass Vases: History & Identification Guide Collection

View all

Swung Glass Vases: History & Identification Guide

Third Stop Vintage Collector’s Guide

How a short glass form becomes a tall vase

A tall neck, an uneven rim and a patterned foot: those are often the first things you’ll notice about a swung glass vase. Take a closer look at how these pieces were made, what the base can tell you, and why two vases from the same mold can look so different.

Shop Swung Glass Vases

L.E. Smith Bittersweet swung vase with ribbed pedestal foot and yellow-orange glass
L.E. Smith Bittersweet: a ribbed pedestal under a long, hand-shaped neck.

What is a swung glass vase?

In the process documented at Fenton, a worker started with a molded glass form. The base was held in a tool called a snap while the top was still hot enough to move. Swinging the piece drew the softened glass out into a longer neck. A worker could reheat the glass as needed to keep shaping it. The base often retained the mold’s pattern, while the height and rim varied from piece to piece. Watch archival footage from the Fenton factory.

Swung glass and stretch glass are different terms. “Swung” describes how the shape was made. Stretch glass refers to a different process that creates an iridescent surface. A tall or irregular rim alone doesn’t tell you what finish was used.

From early carnival glass to mid-century color

Fenton Art Glass. Fenton’s own factory retrospective dates its early swung carnival glass to roughly 1908–1915. Some of those vases began as molds for other shapes, such as spoon holders or celery holders. Fenton returned to the technique in the 1950s and 1960s, including for milk glass bud vases. Fenton factory catalog, p. 28 · Read our Fenton guide.

L.E. Smith Glass. Smith brought out the opaque yellow-to-orange color collectors know as Bittersweet in 1960. The following year its catalog listed eleven swung vase forms in Lilac, part of the Simplicity line. Those examples show how color and form became collecting interests of their own. See the museum’s Lilac examples · Read our L.E. Smith guide.

Viking Glass. Viking’s 1962 catalog illustrates several Epic Six Petal shapes. That’s a useful reminder to compare the entire profile and the underside, not just the number of petals. See the 1962 Viking catalog page.

How to identify a swung vase

  1. Turn it over. Photograph the underside, foot and any label or mark. Note ribs, petals, hobnails or thumbprints. Start with these molded details when comparing catalog examples.
  2. Measure three places. Record the height to the highest point, width of the opening and width of the foot. Height alone is a weak match because a swing can change it.
  3. Check color in daylight. Take a profile photo in neutral light and note whether the glass is transparent, translucent or opaque. Similar colors were made by more than one factory.
  4. Look closely at condition. Inspect the rim and foot for chips, rough spots or repairs. An uneven rim can be part of the original shaping. A line could be a mold seam or a crack; don’t decide from a distant photo alone.

A collector’s example: The Museum of American Glass in West Virginia shows two L.E. Smith Lilac vases that share the same basic form. No. 1902 adds a pulled handle and a seat inside for a taper candle. Those details tell you more than the half-inch height difference between the museum’s two examples.

A good catalog match should agree on several details. If the evidence is mixed, keep the maker tentative rather than relying on color, height or a single feature.

Four examples to compare

Look at the foot and lower body first, then follow the line up to the rim. These photos are from our shop; each listing shows its own details and current availability.

Looking for a particular color, maker or pattern?

Tell us what you’re hunting for. If you have an example to match, start with the measurements and a description of the foot. Or keep exploring with our Vintage Glass Guide.

Help Me Find It   Browse Vintage Glassware